What does FL code mean on a hot tub?
Here’s what to do if your digital spa control throws a FL, FLO, FLOW or similar “low flow” error code at you. Blockages could be caused by a dirty filter, clogged impeller, closed valve or a piece of plastic film covering the spa drain. Low flow can also mean a low water level.
How do you fix the code on a hot tub?
You can try unplugging the hot tub sensor to fix the Sn error code. Wait for a few minutes, then plug it back in. Don’t forget to turn the power off before attempting this. You could also clean or replace the filter cartridges, check whether there are any broken valves, or there’s something stuck in the skimmer.
What are the codes on a hot tub?
Hot tub error codes
- CoLd : Temp in heater housing is below 40° F.
- OH : Overheat.
- HLoH : Hi Limit Over Heat.
- SEoP : Sensor open or disconnected.
- SESH : Sensor short, nonfunctional.
- PSoC : Pressure switch open with circulation pump.
- PSoL : Pressure switch open with low pump.
- PSoH : Pressure switch open with high pump.
How do I reset my leisure Bay spa?
Pull the cover off of the spa and let the water cool for several minutes. When the water has cooled, press any button to reset the sensors and you will see the temperature again.
How do I stop my hot tub from overheating?
How to Stop Your Hot Tub From Overheating
- Turn down the temperature.
- Add cool water.
- Don’t run your filter when it’s hot.
- Add some shade.
What does F6 mean on a hot tub?
The Big List of Spa and Hot Tub Error Codes
| CODE | ERROR CODE DESCRIPTION |
|---|---|
| F2 | 4 hours daily filtration; system message, not an error |
| F4 | 8 hours daily filtration; system message, not an error |
| F6 | 12 hours daily filtration; system message, not an error |
| F | Fahrenheit, used to indicate panel is in Fahrenheit mode |
Is Leisure Bay Spas out of business?
Leisure Bay Spa company is out of business. Leisure Bay spa shells and frames routinely last 30-40 years, but the moving parts behind the access panel door seldom run more than 10 years.
Who makes Leisure Bay hot tubs?
The Celebrity spa models are the Hilo, Bimini, Tonga and Milan. Some different models may have been sold in Europe, including the 4 person Santo, the 6 person Adirondack and the 6 person Galaxy. Most of the Leisure Bay hot tubs have equipment made by major US manufacturers, including Balboa.
What are the names of the Leisure Bay hot tubs?
Leisure Bay Spas has been building hot tubs for over thirty years and has a range of hot tubs built on quality and new innovations in the hot tub market. In the Elite series Leisure Bay Spas boasts 4 different models the Niagara, Hatteras, Cordova, and Harbor Cove.
Who are the owners of Leisure Bay Spa?
The various designs of spas produced offer a lot of choices for customers. The company, Leisure bay industries, began in 1974, with five staffs trading mainly on pools that are above the ground.
What should I do if my Leisure Bay hot tub overheats?
“Overheat” – The leisure bay spas shuts down for this error. Also, the sensors will detect that the hot tub water is 110°F or greater. DO NOT ENTER THE WATER. Remove the spa hot tub hard cover and allow water to cool off. Once the spa cools down to 107°F, the tub should reset on its own.
Are there error codes for digital hot tubs?
The best thing about digital spas and hot tubs – those with a spa side control panel – is that you are given error codes for most equipment problems. Spa error codes can be somewhat cryptic, but when you have the BIG LIST of CODES, you can immediately define the two or three digit source of trouble.
